SDBP40 | 40 ft Bulk Pack Sound Deadening (Entire Car) - 90mil 2.3mm THICK
• Eliminates Road Noise
• 2.3mm (90.55mil) thick for better performance
• Quiets Vibrations
• Stops Rattles
• Increases SPL
• Reduces Heat
• Simple To Install
• Easy To Form Aluminum
• Four Step Peel and Stick Installation
• Ten 18" x 32" Pieces
Benefits of Sound Damping
Sound dampening material is key to reducing the rattles and shakes in your car. It effectively reduces the amount of road noise that is let in through the thin panels of your vehicle. It also lessens vibrations that are created by playing music through your speakers. It works by adding weight to the desired panel, which lowers the resonating frequency. You will notice by adding this material to your car, your sound system will likely get noticeably louder. If you have subwoofers, this is the perfect kit for your vehicle.
Thicker Than the Competition
NVX is one of the world's leading manufacturers of sound dampening material and is up to 30% thicker than the other brands. Don't pay ridiculous amounts of money to kill those rattles, when you can get everything you need from NVX for a fraction of the price. With the SDBP40 dampening material, you will notice a higher quality sound from your system as well as a drastic reduction of road noise. With 40 square feet of material, you will have enough to cover all of those problem areas that have been bothering you for so long!
- Ten 18" x 32" Pieces of Sound Dampening Material
- 90.55mil thick (2.3mm)! There are cheaper, inferior solutions at 50-80mil, but we do not recommend that thin of a solution as it will not perform as well.
- 40 Square feet total
- Complete sound damping kit for the entire vehicle/car. Can be used for areas such as the trunk, doors, roof, and floor
- Made from 100% Butyl Rubber
- Eliminates road noise
- Quiets vibrations
- Increases sound quality and output of the car audio system
- Stops rattles
- Increases SPL
- Reduces heat
- Easy to form aluminum conforms to the desired area of the vehicle with ease
- Four-step peel and stick design for easy installation
- Up to 30% thicker than the leading competitors
- 1-year Manufacturer's Warranty
- Dimensions (each piece): 18"L x 32"W
How to Install Sound Damping Properly
Sound damping can be a very beneficial accessory to reduce noise and vibration. To take full advantage of this soundproofing, read these instructions carefully, and follow them till the end. It’s important to familiarize yourself with all the details to install the sound damping correctly. Incorrect installation will result in less than desirable results.
|The first step is to decide which location in your car you want to insulate. These locations include the floorboards, roof, door panels, trunk, or firewall. We recommend soundproofing all metal surfaces for maximum sound deadening performance. Next, refer to your vehicle’s service manual for information on how to dismantle the trimming panels. Be careful when removing the panels to avoid breaking the fixing clips.|
Once the trimming is dismantled, remove the remainder of the factory insulation if it is damaged. If it is still intact, there is no need to permanently remove it. Next, you need to properly clean, dry, and degrease the prospective surface. Sound deadening won't adhere properly if applied to a wet or dirty surface. Use a metal surface cleaner or degreaser along with a dry, clean rag. Make sure to use gloves and apply the degreaser in a well-ventilated space.
|For this step, measure the prospective surface you are going to treat. To make things easier, make a template of the appropriate size on a large sheet of paper and then transfer it to the damping material. That will make it easier to install it more accurately and avoid wasting material. Use a utility knife to cut the desired shape and size. Be careful and use gloves to protect your hands.|
|Place a sheet of sound damping to the surface without removing the protective film. If it covers the surface properly, you are ready to install it. Gradually remove the protective paper film as you apply it to the surface for better adhesion. Once on the surface, press it down firmly until it is set in place. Flatten it with your hands to avoid unnecessary air bubbles. Use a rolling tool like the NVX SDRLR1 to press the mat down to the metal surface. Go across the entire surface with the roller to ensure that the sheet is installed properly.|
|Once all sound deadening is in place, simply reinstall all trim pieces and carpet back to its original placement. Now you are ready to enjoy higher sound quality with fewer vibrations.|
|Item Returns||This item can be returned|